HP9000 Containers and PSET
Hello,I need to create an HP9000 System containers to support an old HPUX 11iv1 server.The itanium server is a rx2800 i4 with 16 Cores and 64Gb of RAM.I need to present only two CPU from the itanium...
View ArticleHaving issues installing hp-snmp-agent
First time post!Having difficulties installing hp-snmp-agent and other hp-health items on HPDL380G6.Dependency issues. OS is CentOS 7.2. I see one of the dependencies. Is there a single place to...
View ArticleIntegrity BL890c i4 server Some Nic Ports Down.
Hi, We have a Integrity BL890c i4 server, with a virtual connect configured, suddenly we have 3 nics down on the hpux 11.31 server, i'm going to use only 1 for the example lan8: mhv:#/root# nwmgr -S...
View ArticleAll pic slots off following power outage
Hi,Following a recent power outage on our RX7620 all pci-x power slots are in state off as reported by olrad -q# olrad -qDriver(s)CapableSlot Path Bus Max Spd Pwr Occu Susp OLAR OLD Max ModeNum Spd...
View ArticleILO 2 - cabinet 0 failure detected error - HPsuperdome server SD32B
Good morning, A Failure detected yellow LED is showing on cabinet 0 on one of our HP superdome server SD32B. According to the event log below the associated error was caused by correctable single bit...
View ArticleOA don't show the SAN disk path
I want to install hp-UX VSOE on SAN disk in superdome-2. So for this, at first I assign a SAN disk by mapping to that server(nPar). Then I connect DVD for OS by Monarch OA CLI. And then try to...
View ArticleIn uefi lanboot select doesn't show all HP NC532m Dual Port Flex-10 virtual nics
Hi,I am on a bl870c that has a HP NC532m Dual Port Flex-10 mezzazine card installed.I don't know if it's supposes to work this way, but only 1 vnic per HP NC532m port is available in the UEFI shell.I...
View Articlewbem
Hi,I just notice an error in my syslog and I'm unable to find why, any help would be appreciated.May 26 13:56:25 cimservera[29650]: [Authentication failed] Password not validMay 26 13:56:27...
View ArticleIntegrity server problem, shuts down
The Integrity rx2660 system has just shutdown on its own twice in the past week. There is some problem with it. The System Health and Internal Health LEDs were flashing amber or red. The logs...
View ArticleP410i Array Controllers Handling Predictive Failures
I've had the same problem on various servers using P410i array controllers. Replacing drives in predictive failure with known good drives will not clear the predictive failure. The drives are replaced...
View ArticleSuper dome event
Alert level 2: InformationalKeyword: CACHE_CHECK_INFOIt indicates a cache error occurred and data field contains check info data.Reporting Entity: System Firmware located in cabinet 0, slot 4, cpu...
View ArticleIR volume disque missing
ir volume : primary ok secondary missing apres echange du disque idem ioscan : un disque (autre path) en supplementRaid Level : RAID 1Volume sas address : 0x5605d6c74ffa0d2Device Special File :...
View ArticleCron script not running
Hello,When i run cron job its not runnning it getting error message...but when i run the script manuall its running without problem....Script file...prodata1#more /tmp/tar#!/bin/sh -xsu - dbprod -c...
View Articlerx2800 P410i Controller
I have a rx2800 integrity server with a Smart Array P410i Controller.At start I have the Controller in HBA modeHow to change the mode in RAID?I already update SAS io firmware at version 6.42, but the...
View ArticleRx8640 stuck at the MP login prompt
I have a RX-8640 stuck at the MP Login prompt. How do I get back to the console? Other than resetting the power? I don't know the MP password, nor does Control-B work.
View ArticleHow to go from MP menu to EFI shell
This is on rx-8640 Itanium. I am booted into MP menu. What next step do I take to get into EFI?
View ArticleUnable to select FS0: to boot off the CD
I cannot boot off the CD, when I do map -r I get just one LUN device. I cannot select any FSx: at all. reconnect -r shows 11 devices
View ArticleMP Console not responding
Has anyone seen this behavior before, or can anyone offer advice.I had a problem with this server (bl860c blade in c7000 enclosure, using Virtual Connect). The server has been running without a...
View ArticleHow to reset console on a rx8640?
The console keeps writing junk to the screen, with every line that is displayed or typed. You can still see the text you type but it's surrounded by junk.
View Article