All pic slots off following power outage
Hi,Following a recent power outage on our RX7620 all pci-x power slots are in state off as reported by olrad -q# olrad -qDriver(s)CapableSlot Path Bus Max Spd Pwr Occu Susp OLAR OLD Max ModeNum Spd...
View ArticleILO 2 - cabinet 0 failure detected error - HPsuperdome server SD32B
Good morning, A Failure detected yellow LED is showing on cabinet 0 on one of our HP superdome server SD32B. According to the event log below the associated error was caused by correctable single bit...
View ArticleDIMM slots for rx2800
Greetings !! I have some rx2600 in my enviornment , and cstm works fine if i want to know memeory occupancy in it.Memory Board Inventory DIMM Location Size(MB) DIMM Location...
View ArticleIn uefi lanboot select doesn't show all HP NC532m Dual Port Flex-10 virtual nics
Hi,I am on a bl870c that has a HP NC532m Dual Port Flex-10 mezzazine card installed.I don't know if it's supposes to work this way, but only 1 vnic per HP NC532m port is available in the UEFI shell.I...
View ArticleIntegrity server problem, shuts down
The Integrity rx2660 system has just shutdown on its own twice in the past week. There is some problem with it. The System Health and Internal Health LEDs were flashing amber or red. The logs...
View Articlewbem
Hi,I just notice an error in my syslog and I'm unable to find why, any help would be appreciated.May 26 13:56:25 cimservera[29650]: [Authentication failed] Password not validMay 26 13:56:27...
View ArticleP410i Array Controllers Handling Predictive Failures
I've had the same problem on various servers using P410i array controllers. Replacing drives in predictive failure with known good drives will not clear the predictive failure. The drives are replaced...
View ArticleSuper dome event
Alert level 2: InformationalKeyword: CACHE_CHECK_INFOIt indicates a cache error occurred and data field contains check info data.Reporting Entity: System Firmware located in cabinet 0, slot 4, cpu...
View ArticleIR volume disque missing
ir volume : primary ok secondary missing apres echange du disque idem ioscan : un disque (autre path) en supplementRaid Level : RAID 1Volume sas address : 0x5605d6c74ffa0d2Device Special File :...
View ArticleRx8640 stuck at the MP login prompt
I have a RX-8640 stuck at the MP Login prompt. How do I get back to the console? Other than resetting the power? I don't know the MP password, nor does Control-B work.
View ArticleHow to go from MP menu to EFI shell
This is on rx-8640 Itanium. I am booted into MP menu. What next step do I take to get into EFI?
View ArticleHow to reset console on a rx8640?
The console keeps writing junk to the screen, with every line that is displayed or typed. You can still see the text you type but it's surrounded by junk.
View ArticleUnable to select FS0: to boot off the CD
I cannot boot off the CD, when I do map -r I get just one LUN device. I cannot select any FSx: at all. reconnect -r shows 11 devices
View ArticleMP Console not responding
Has anyone seen this behavior before, or can anyone offer advice.I had a problem with this server (bl860c blade in c7000 enclosure, using Virtual Connect). The server has been running without a...
View ArticleUnable to connect to the MP console
It used to work but suddenly I can no longer connect. No changes have been made configuration-wise. This is what I get. 11.31 rx8650 and I telnet from another box. I check the config at the MP prompt....
View ArticleHow to add an option to boot profile?
reconnect -rBroadcom NetXtreme Gigabit Ethernet (BCM5703) is detected (PCI-X)Scsi(Pun2,Lun0) _NEC DVD_RW ND-3540A 1.30 ( 40 MBytes/sec)Scsi(Pun5,Lun0) HP Ultrium 3-SCSI G54D ( 80 MBytes/sec)HP 2Port...
View Articlehpsum: how get out of INSTALL state
I'm trying to use hpsum CLI to downgrade some firmware on a bl870c i2.How do I get my node out of the INSTALL state and UserActionNeeded_phase?(this forum interface really sucks: I can't use ctrl-v to...
View ArticleDriver for Ethernet Card on RX2800 i2 server
I am trying to find out what Ethernet Card I have in my Integrity Server RX2800 i2 and also how to upgrade the driver.System runs Open VMS 8.4
View Articlerx7640 not showing all 4 internal disks
Hi All,im having the following issue with an rx7640 server in fact, i need to install 11iv3 on this newly acquired server however, at early boot stages the server is only showing/detecting 2 internal...
View Article