cc command failed with:
Sorry, command failed: RtnCodeIoBayNotAttachedToCell
io command shows no io chassis connected to any cell:
[mp0013217c7543] MP:CM> io
--------------------------+
Cabinet | 0 | 1 |
--------+--------+--------+
Slot |01234567|01234567|
--------+--------+--------+
Cell |XXX.....|........|
IO Cab |........|........|
IO Bay |........|........|
IO Chas |........|........|
Following is the ps> cabinet 0 output:
[mp0013217c7543] MP:CM> ps
This command displays detailed power and hardware configuration status.
The following MP bus devices were found:
+----+-----+-----------+----------------+
|Cab.| | UGUY | Cells |
| # | MP | CLU | PM |0 1 2 3 4 5 6 7 |
+----+-----+-----+-----+----------------+
| 0 | * | * | * |* * * |
You may display detailed power and hardware status for the following items:
B - Cabinet (UGUY)
C - Cell
M - MP
Select Device: b
Enter cabinet number: 0
HW status for SD32B compute cabinet #0: FAILURE DETECTED
Power switch: on; Power: enabled, good; Door: open
Fan speed: normal; Temperature state: 29 C, normal
FANS OR BLOWERS NOT REDUNDANT; BPSs redundant; Clocks UNDEFINED;
+------+--------+-----------------+---------------------+
| | Main BP| | IO Backplanes |
| | Power | | IO Bay 0 | IO Bay 1 |
| Main | Boards | Cells | Chassis | Chassis |
| BP | 0 1 | 0 1 2 3 4 5 6 7 | 0 1 2 3 | 0 1 2 3 |
+---------------+------+--------+-----------------+----------+----------+
| Populated | * | | * * * | * * | * |
| Power Enabled | * | | * * * | * * | * |
| Powered On | | | | | |
| Power Fault | | | | | |
| Attention LED | | | | | |
+-------------+---------+-----------+
| | Cabinet | IO |
| BPS | Blowers | Fans |
| 0 1 2 3 4 5 | 0 1 2 3 | 0 1 2 3 4 |
+-----------+-------------+---------+-----------+
| Populated | * * * * * | * * * | * * * * * |
| Failed | | | |
Please type <CR> to continue, Q to quit, or S to stream:
Voltage margin: nominal; Clock margin: nominal
+-------------------------------------------+
| Backplane Power Converter Faults |
| | VRM Slot | |
| 12V | 3.3V HKP | 3.3V | 1 2 3 4 5 6 | LED |
+-----+-----+----------+------+-------------+-----+
| PS0 | | | | | |
| PS1 | | | | | |
LED states: G - on green (no faults)
YB - blinking yellow (fault detected)
+------------------------------------------+
| Backplane Power Faults |
| | | | 2.5V |
| 1.2V | 2.5V | | |00 40 01 41 02 42|
+-------+------+------+ +-----+-----------------+
| RPM0 | | | | XBC | |
| RPM1 | | |
| RPM2 | | |
| OSP | | |
Please type <CR> to continue, Q to quit, or S to stream:
CLU Status PM Status CLU POST
UGUY LEDs: **______ **** ____
+---------------------------------------------------------------------------+
| IO Backplane Power Fault & Temp Status |
| Physical | |
| Location |Type | Revision |+12V |-12V |+1.5V| +5.0V | +3.3V |LED|
|Cab#/Bay#/Slot#| | | 0 1 | 0 1 | 0 1 | 0 1 2 | 0 1 2 3 | |
+---------------+-----+-------------+-----+-----+-----+-------+---------+---+
| 0/0/1 | i | 000.000.000 | | | | | | |
| 0/0/3 | i | 000.000.000 | | | | | | |
| 0/1/3 | i | 000.000.000 | | | | | | |
+---------------+-----+-------------+-----+-----+-----+-------+---------+---+
Key: . - Present; * - Powered; F - Faulted; T - Overtemp
LED states: G - Green on (no faults)
Y - Yellow on (redundant fault detected)
YB - Yellow blinking (non-redundant fault detected)
IO Backplane types: i - PCI-X IO Backplane (IO LPM type is IO_LPM)
e - PCI Express IO Backplane (IO LPM type is IO_LPM_E)
Following is the ps> cell 0 output:
[mp0013217c7543] MP:CM> ps
This command displays detailed power and hardware configuration status.
The following MP bus devices were found:
+----+-----+-----------+----------------+
|Cab.| | UGUY | Cells |
| # | MP | CLU | PM |0 1 2 3 4 5 6 7 |
+----+-----+-----+-----+----------------+
| 0 | * | * | * |* * * |
You may display detailed power and hardware status for the following items:
B - Cabinet (UGUY)
C - Cell
M - MP
Select Device: c
Enter cabinet number: 0
Enter slot number: 0
HW status for Cell 0 in cabinet 0: FAILURE DETECTED
Cell power status: enabled, OFF, no fault, NVRAM battery LOW
Boot is blocked
PDH shared memory is not-initialized
Cell DISABLED by PDHC: bad CPU module FRUID checksum
Cell Complex Compatibility: B
Cell Partition Compatibility: .
CPU Compatibility: .
Cell Attention LED is off
PDH status LEDs: ____
Core cell is INVALID
IO cable status: IO IN AND OUT CABLES STATUS UNDEFINED
IO cable connection physical location: cabinet 0, IO bay 0, IO chassis 0
+-----------------------------+ +--------------------------------------------+
| CPU Modules | | DIMM Presence |
|Populated| Faulted | Enabled | | Side: | A | B |
| 0 1 2 3 | 0 1 2 3 | 0 1 2 3 | | Echelon: |0123456789ABCDEF|0123456789ABCDEF|
+---------+---------+---------+ +----------+----------------+----------------+
| | | | | |* | |
Please type <CR> to continue, Q to quit, or S to stream:
+-------------------------+
| PDH Power Module Faults |
| 1.2V PDH | 2.5V PDH |
+------------+------------+
| * | * |
+-------------------------------------------------------------------------+
| Cell Board Power Module Faults |
| 1.5V SKY | 1.2V FSB | 2.5V L2C | 3.3V HKP | MISC LDO |
| 0 1 2 | 0 1 2 | 0 1 | 0 1 | 0 1 2 3 4 5 6 7 8 9 a b c d |
+----------+----------+----------+----------+-----------------------------+
| | | | | * * |
+----------------------------------------------------------+
| Cell Power Board Power Module Faults |
| 1.8V MEM | 1.8V AB-IO | 1.5V AB-CORE | 12V IF | 3.9V IF |
| 0 1 2 3 4 | 0 1 | 0 1 | 0 1 | 0 1 |
+-----------+------------+--------------+--------+---------+
| | | | | |